instruction stringclasses 1
value | input stringlengths 1 6.57k | output class label 2
classes |
|---|---|---|
Predict the fatality based on the description. | At approximately 9:00 a.m. on October 16, 2014, an employee arrived at a home ow ners residence. They discussed the solar water heater and the employee decided to take a closer look. The employee got the Werner 300 pound rated, 13 foot extension ladder out of the truck and placed it on the driveway and extended the ra... | 11 |
Predict the fatality based on the description. | at 6:30 p.m. on June 6, 2018, Employee #1 and a coworker were utilizing a hydraulic lift table to transport a 578 pound metal ring to work bench number 10. As t hey attempted to slide the metal ring off of the hydraulic lift and onto the work bench, the ring slid off and landed flat side down. Employee #1's left hand w... | 00 |
Predict the fatality based on the description. | At 5:20 a.m. on August 1, 2017, Employee #1 was cutting the end of a cardboard b ox to gain access to the parts at the bottom, using a dull razor knife that was brought from home, which was against company policy. The knife slipped and the employee sustained a deep laceration to his lower left side bicep, requiring hos... | 00 |
Predict the fatality based on the description. | At 4:30 p.m. on November 1, 2018, an employee was installing vinyl plank flooring in a single family home. While using a table saw to cut a flooring plank, the unguarded blade made contact with the employee's left hand. The saw blade lacerated the palm side of the employee's left index, middle, ring and small fingers w... | 00 |
Predict the fatality based on the description. | At 10:00 a.m. on February 11, 2020, an employee was charging a JI Case Man# 30-4 trenching digger's battery with an AC battery tender when he suffered a persona l health related issue. The employee was found face down with the left rear tire positioned between his shoulders. The employee was pronounced dead at the scen... | 11 |
Predict the fatality based on the description. | On October 3, 2013, Employee #1, a 43-year-old male, oiler, with Collins Management Corporation, was on top of a 14 foot high deck, oiling a motor. The deck was covered with wood debris: Employee #1 walked on top of a hole covered by debris and fell approximately 14 ft to the concrete floor below. Employee #1 was hospi... | 00 |
Predict the fatality based on the description. | At 12:00 p.m. on August 8, 2017, Employee #1, employed by a construction company, was engaged in framing work at a multiemployer construction project, a new two -story house. A crane was being used to lower trusses onto the roof. A truss f ell from the crane onto the roof and shook the house. Employee #1 fell, a fall h... | 00 |
Predict the fatality based on the description. | At 9:15 a.m. on July 3, 2018, an employee was operating a concrete saw (Husqvarn a K970 concrete saw), cutting into a concrete sewer pipe as part of a pipe installation. As the employee cut through the concrete pipe, the saw kicked back and struck the employee in the neck. The employee received a laceration to his neck... | 00 |
Predict the fatality based on the description. | At 2:00 p.m. on March 6, 2020, an employee was working at an automotive body shop. It was one outlet of a nationwide chain of auto body shops. The employee was an auto body technician. He was straightening the rear body panel of a vehicle being repaired. He was using a chisel and hammer. When he struck the hammer again... | 00 |
Predict the fatality based on the description. | At 8:00 p.m. on June 6, 2017, an employee performing servicing on a My Center Sp ark Changer. As the employee reached for a tool, it fell and landed in the pallet changer portion of the equipment. She immediately reached down to pick up a tool, when her right hand became caught in the rotating pallet used to move parts... | 00 |
Predict the fatality based on the description. | At 11:00 a.m. on January 22, 2013, an employee was performing upgrades to a camp us electrical distribution switchgear. The employee was working with phase volta ge that measured 4,160 volts AC from phase and 23,000 volts AC from phase to ground. Using a utility knife, the employee was installing bus extensions when he... | 11 |
Predict the fatality based on the description. | At 10:30 a.m. on December 27, 2017, Employee #1, a fire fighter, and another fireman were dispatched to a split level single family home with no fire showing fr om the outside. When the two entered the house, they found a couch on fire in th e step-down family room. As they were fighting the fire, they ran out of water... | 00 |
Predict the fatality based on the description. | At 11:30 a.m. on April 17, 2019, an employee was working for a city school district. She was working at an elementary school. She was standing in the school yard, supervising children during meal time. She lost consciousness and fell from t he same surface onto a concrete cement surface. She suffered an unspecified hea... | 00 |
Predict the fatality based on the description. | At 10:30 a.m. on July 5, 2019, an employee was tying an extension ladder to the fascia board of the roof. The ladder started sliding to the left side, and the employee jumped to his right, approximately seven feet onto the ground. The employee was hospitalized to treat a fractured right leg. | 00 |
Predict the fatality based on the description. | At 7:30 p.m. on February 25, 2016, an employee who just arrived at the worksite was exiting a truck, slipped on ice, and struck his head on the asphalt parking lot. Following the incident, the employee told co-workers about the incident an d said did not feel well. The employee was admitted to the hospital, developed a... | 11 |
Predict the fatality based on the description. | At 11:00 a.m. on November 25, 2013, an employee and coworker were walking southbound on new pavement that had been laid. The employee continued their inspection when the coworker stopped to take a call on their cellphone. The employee stepped back onto the road and a dump truck traveling southbound in reverse to unload... | 11 |
Predict the fatality based on the description. | At 10:45 p.m. on February 3, 2020, an employee working as a packaging line operator for a food manufacturer was loading cardboard packaging material into a packaging machine located at the Tetra packaging line (Line F). The employee was moving a cart containing palletized cardboard into position on the in-feed end of t... | 00 |
Predict the fatality based on the description. | At 1:30 p.m. on April 8, 2019, an employee was installing brake lines on Toyota Tacoma truck when the truck cab fell on top of him, fracturing his ankle and leg. The employee was hospitalized. | 00 |
Predict the fatality based on the description. | At approximately 1:00 a.m. on March 14, 2017, Employee #1 was pulling two pieces of metal rectangular tubes measuring approximately 3-inch by 6-inch by 9.67 foot long and weighing approximately 175 pounds. The metal tubes were stored leaning against a wall with other materials unrestrained. He was trying to transfer t ... | 11 |
Predict the fatality based on the description. | At 7:30 a.m. on December 4, 2018, an employee was clearing some debris from a punch hole machine and placed her left hand's index finger in the hole when a maintenance technician cycled the machine manually. The employee caught her finger and amputated it. The employee was hospitalized. | 00 |
Predict the fatality based on the description. | At approximately 2:30 p.m. on December 30, 2013, Employee #1, a framer employed by Old Ranch Construction: Coworker #1, the owner of the company: and Coworkers #2, #3, #4, and #5, also framers, were working at a new residential building project. Coworker #1 asked Employee #1 and the other workers to assist him in manua... | 00 |
Predict the fatality based on the description. | At 2:45 p.m. on October 5, 2022, an employee was tripping out 4 inch drill pipe to locate a leak somewhere in the drill string. The employee was holding a 4 inch rubber hose around the drill pipe to clean it as it was coming out of the hole in an attempt to locate the leak. During the removal of the string, the drill p... | 00 |
Predict the fatality based on the description. | At 1:52 p.m. on March 9, 2021, an employee went onto the roof of a building to trouble shoot and repair HVAC equipment. The employee was later found lying between two HVAC units and emergency services were called. The employee was determine d to have been killed by natural causes. | 11 |
Predict the fatality based on the description. | At 6:45 a.m. on May 15, 2019, Employee #1, employed by a construction company, w as engaged in exterior masonry work at a multiemployer building site. He attempted to access the 32-foot high work platform of a mast scaffold by climbing over a concrete wall, part of an unfinished parking garage, and lowering himself to ... | 11 |
Predict the fatality based on the description. | An employee was working at a general medical or surgical hospital. He transported patients throughout the hospital. He contracted COVID-19. At 10:00 a.m. on April 5, 2020, he was hospitalized. | 00 |
Predict the fatality based on the description. | At 2:00 p.m. on March 8, 2021, an employee and a coworker were loading a refrigerator onto the bed of a pickup truck. The employee and coworker had already move d all of the loose items in the truck bed to the right side of the bed as they l aid the refrigerator down on the left. As they laid the refrigerator down, the... | 11 |
Predict the fatality based on the description. | An employee last worked in the office on July 27, 2021, before it was closed on July 28, 2021, due to a COVID-19 outbreak. The employee first had symptoms on July 29, 2021, tested positive on August 2, 2021, and went to the hospital several times, and was released each time released until admitted on August 8, 2021. Th... | 00 |
Predict the fatality based on the description. | At 7:00 a.m. on December 29, 2017, an employee was reopening a 7 foot deep by 5 foot wide trench. The employee was struck in the head and chest by sand bags th at were filled with crushed rock, killing the employee. The employee suffered a crushed chest and heart attack. | 11 |
Predict the fatality based on the description. | At 8:05 a.m. on May 10, 2017, an employee was in the process of refurbishing a m ulti-former headbox (paper machine). The employee removed the last of 51 bolts f rom the top section (roof member) of the head box. The top section sits on the bottom section at a 40-50 degree angle. The roof member weights approximately 4... | 00 |
Predict the fatality based on the description. | At 8:53 a.m. on April 27, 2018, an employee was adjusting the exit end of a water jet when he hit the wrong button that operates the loom. The employee partially amputated his left hand's middle finger in the loom. The employee was hospitalized. | 00 |
Predict the fatality based on the description. | At 3:00 p.m. on April 6, 2022, an employee and three coworkers on scaffolding, removing work forms from the wall of a stairwell on the first floor. The employee fell approximately 17 feet from the first floor to the cellar, injuring his head and torso on the concrete floor. The employee was killed due to multiple blunt... | 00 |
Predict the fatality based on the description. | On March 30, 2020, an employee was infected with COVID-19 and died later. Exposure was not work-related. | 00 |
Predict the fatality based on the description. | At 2:30 p.m. on January 9, 2017, an employee was operating an overhead crane cha in hoist to lower equipment. The chain collection metal box that was attached to the hoist unexpectedly detached from the hoist and struck the employee. He sustained lacerations to his face, and he was hospitalized for his injuries. his in... | 00 |
Predict the fatality based on the description. | At 12:00 a.m. on March 13, 2018, an employee was operating a mechanical grinder and feeling the smoothness of the surface being ground. The employee's left hand came in contact with the grinding stone resulting in the amputation of two finger tips. | 00 |
Predict the fatality based on the description. | At approximately 12:30 p.m. on March 27, 2013, Employee #1, a foreman, was inspecting the sheeted roof of a two story residential single family home that was under construction. The employee was wearing a full body harness with a lanyard. T he lanyard was connected to a 0.5 in. in diameter by 50-ft long rope. The other... | 00 |
Predict the fatality based on the description. | At 9:30 p.m. on September 28, 2018, an employee was opening a column mold to clean it and twisted as he raised it. The employee caught the hold handle on the m old stop and amputated his left hand's ring finger. The employee was hospitalized. | 00 |
Predict the fatality based on the description. | At 1:00 p.m. on October 10, 2017, an employee was walking on a roof to inspect f or rat entry points, when he fell through a skylight. The employee struck a ware house floor below and sustained several broken bones, which he was hospitalized and received treatment. | 00 |
Predict the fatality based on the description. | At 9:30 p.m. on February 22, 2019, an employee was collecting shopping carts in a parking lot when she slipped on ice and fell to the pavement. The fall resulted in a fracture of the wrist and knee and tailbone injuries. | 00 |
Predict the fatality based on the description. | At 10:45 a.m. on May 26, 2017, an employee was fixing the yellow canopies under the conveyors above a bread slicer line. The employee fell and fractured right wrist and elbow. | 00 |
Predict the fatality based on the description. | At 12:00 p.m. on October 11, 2018, Employees#1 was operating the stabilizer, delivering and unloading roofing materials. He reached between the flat bed and the stabilizer, while it was moving up, to grab a chain and attach it to the stabilizer for securing purposes. His hand became caught and pinned against the flat b... | 00 |
Predict the fatality based on the description. | At 10:00 a.m. on July 5, 2018, Employee #1, employed by a framing construction company, was engaged in framing work at a two-story multifamily residential structure. He was using a hammer to nail a piece of hardware to the framing when a n ail ricocheted and struck his eye. Emergency services transported the employee t... | 00 |
Predict the fatality based on the description. | At 12:00 noon on August 19, 2021, an employee was standing at a coffee table in the skilled care serving line when she turned around and tripped and fell backwards into the coffee table. The employee hit her head on the coffee table and the employer convinced her to go to the hospital, where she died four days later du... | 00 |
Predict the fatality based on the description. | At 10:25 a.m. on June 21, 2017, an employee was using an overhead bridge crane t o unload a bundle of steel from a flatbed trailer. During operation, the employee inadvertently pressed the wrong button on the crane's remote control and the load swung in his direction. The employee was struck by the load and was pinned ... | 00 |
Predict the fatality based on the description. | At 4:00 p.m. on January 11, 2021, Employee #1 from Police Department #1 responded to a vehicle crash when one of the drivers involved in the crash opened fire o n him with an AK-47 killing him instantly. The driver then car jacked a vehicle and took off toward the airport. Employee #2 from and Employee #3, both from Po... | 11 |
Predict the fatality based on the description. | At 1:13 p.m. on December 15, 2021, an employee was using a manual control to walk tail stock into a plug used to help hold the part in place on a lathe. The employee walked the stock in too far with his left hand between the plug and the part. The tail stock made contact with the plug and pressured in place, striking t... | 00 |
Predict the fatality based on the description. | At 12:30 p.m. on September 6, 2017, Employee #1 was climbing a ladder to access the storage mezzanine. The employee fell off the ladder, sustaining a concussion, inflammation in abdomen, and bruising over her body. She was hospitalized for treatment. | 00 |
Predict the fatality based on the description. | At 3:56 p.m. on April 16, 2016, an employee was installing shingles on a roof when he suffered a heart attack and died. | 11 |
Predict the fatality based on the description. | On November 17, 2017, an employee was installing metal plates to the I-beam and was burned by a combustible dust fire that broke out. The employee suffered skin burns and was hospitalized. | 00 |
Predict the fatality based on the description. | At approximately 11:15 a.m. on February 22, 2016, Employee #1 was working in and around a large timber log pile. Employee #1 was killed by a log which fell and struck him. | 11 |
Predict the fatality based on the description. | An employee was working for County law enforcement. The employee began to exhibit COVID-19 related symptoms, tested positive for COVID-19, was hospitalized and died from complications related to COVID-19 on November 16, 2021. The date, time and other details leading up to exposure are not indicated in the narrative. In... | 00 |
Predict the fatality based on the description. | At 9:00 p.m. on October 24, 2018, an employee was troubleshooting a furnace. He opened the hatch on the incorrect furnace and sustained 2nd and 3rd degree burns to face, neck, and arm from the furnace flames. | 00 |
Predict the fatality based on the description. | At 6:45 a.m. on October 7, 2019, an employee was holding a metal block on the underside of a trailer wall panel in order to tack a rivet into the wall and top r ail. Coworkers, working on the other side of the conveyor line, pulled on the wall panel causing the employee's left thumb to get caught between the conveyor f... | 00 |
Predict the fatality based on the description. | At 4:00 p.m. on July 11, 2018, Employee #1 was operating the Accu Press Shear. A s the employee pushed the material into the shear for the last cut, his finger s lid under the hold down clamp of the machine. His left middle finger tip was smashed and later had to be amputated. | 00 |
Predict the fatality based on the description. | At 12:00 a.m. on September 8, 2021, an employee worked a coworker and the operator of a milling machine in a highway work zone while the milling machine ground up asphalt for road work. At some point, the operator of a semi-truck with a low boy trailer pulled into the work zone in preparation to load the milling machin... | 00 |
Predict the fatality based on the description. | Three employees were working for a construction company when they contracted COVID-19. Employee #1, a senior project manager, and Employee #2, a project coordinator, were working in the office. Employee #1 had his own office and employee #2 was working in a cubicle more than six feet away from employee #1. Employee #3,... | 00 |
Predict the fatality based on the description. | On October 1, 2021, a security guard was working behind the front desk at a client location when he was shot and killed by a tenant wielding a zip gun. | 00 |
Predict the fatality based on the description. | At approximately 10:57 a.m. on April 11, 2013, Employee #1, with Ming International Dba Carpet Solutions Inc., was removing nylon carpet fibers from between the line "B" grinding machine's moving conveyor belt's tail roller and conveyor bel t. As Employee #1 removed the fibers from the moving tail roller, Employee #1's... | 00 |
Predict the fatality based on the description. | At 4:00 p.m. on March 14, 2020, an employee was testing a specimen sorting machine when he turned it on while he had his hand resting on unguarded rollers. The employee suffered a right index finger amputation, and he was hospitalized. | 00 |
Predict the fatality based on the description. | At 2:45 p.m. on August 18, 2022, an employee was taping off a bathroom to begin bathtub refinishing work. The employee had not yet begun the refinishing work when he died. The death certificate indicated the employee died from natural causes. | 00 |
Predict the fatality based on the description. | At 3:00 p.m. on January 18, 2014, an employee was performing a rig up operation of the substructure (derrick tower). The employee used a 12 pound sledge hammer to remove the 8 inch x 3 inch diameter pin from the left crown support bracket a nd when the pin was removed the right crown support bracket failed. The middle ... | 11 |
Predict the fatality based on the description. | On December 12, 2017, an employee was working for a charter bus transit system based at a university. He was driving a bus, when he got in an argument with a coworker. The argument escalated, and the coworker pulled out a gun. He shot the employee and ran him over with a bus. The worker sustained a broken arm and lacer... | 00 |
Predict the fatality based on the description. | At 13:30 p.m. on August 17, 2022, an employee was working as a roofer and with two coworkers to remove and replace fascia boards on an apartment building. After having lunch, the employee was going up 32-foot, type 1AA fiberglass extension ladder (Sunset Ladder Co., Model FE1AA32) to start working. The ladder was not f... | 00 |
Predict the fatality based on the description. | At 2:30 p.m. on December 3, 2021, an employee became trapped while submerged under water retrieving golf balls and was killed due to drowning. The employee was found by a coworker floating on top of the water unresponisve. | 00 |
Predict the fatality based on the description. | At 6:50 p.m. on April 8, 2017, Employee #1, a turbine mechanic, and a coworker w ere attempting to reposition a load on a long flatbed truck. The load consisted of a combustor and a stand that weighed approximate 26,500 pounds. The coworker tried to release a lever style chain binder by hand, but that attempt was unsuc... | 00 |
Predict the fatality based on the description. | At approximately 7:45 a.m. on April 16, 2013, an incident occurred where Employe e #1, a warehouse manager, was removing a wire which was wrapped around steel beams and the beams fell off on his left thumb. Employee was transported to a local hospital where his thumb was amputated. | 00 |
Predict the fatality based on the description. | At 3:30 p.m. on November 6, 2019, an employee working as a Laborer for a hardwood manufacturer was cleaning glue off the rollers of a coating machine with a rag. The rollers caught the rag which pulled the employee's right arm into machine. The employee fractured her arm, shoulder, collarbone, and ribs and required hos... | 00 |
Predict the fatality based on the description. | At 11:15 p.m. on January 31, 2019, an employee was stamping numbers on a part an d was using a foot pedal to actuate the press. The employee crushed and amputated her finger when the press closed on it. The employee was hospitalized. hospitalized. | 00 |
Predict the fatality based on the description. | At 4:30 p.m. on February 14, 2019, an employee was operating a conveyor by its foot pedal when he noticed that it was not operating properly. The employee reached under the conveyor to see if there were some debris that was causing the malfunction and caught his right hand's index finger with the chain and sprocket. Th... | 00 |
Predict the fatality based on the description. | At 9:20 p.m. on January 29, 2018, an employee was working for a janitorial service. He was cleaning an atrium area on the second floor. There were tiled runways that ran across the atrium. The runways had sides that were 36 cm (14 inches) high. These areas were not intended for people to walk on. They were decorative. ... | 11 |
Predict the fatality based on the description. | At 7:30 p.m. on June 9, 2018, an employee was spray-painting a metallic electric conduit with aerosol paint. An electrical discharge punctured the spray paint a nd caused ignition. The employee was electrocuted. | 11 |
Predict the fatality based on the description. | At 10:30 a.m. on January 23, 2020, an employee working for a tree service was working to remove 3 palm trees inside the atrium of a hotel. The employee was work ing with two coworkers to complete the job. The employee was the Lead and was th e tree climber with the two coworkers working as Ground Crew Workers. The crew... | 00 |
Predict the fatality based on the description. | At 12:45 a.m. on February 15, 2019, an employee was clearing a piece of material from the point of operation on a machine and reached behind a guard. The employee caught and amputated two of his fingers when the machine cycled. The employee was hospitalized. | 00 |
Predict the fatality based on the description. | An employee had worked as a Facility Engineer for a research hospital. The employee last worked on December 30, 2020 and was hospitalized starting January 7, 2021 until January 13, 2021 for COVID-19. The date, time and other details leading up to exposure are not indicated in the narrative. Information regarding engine... | 00 |
Predict the fatality based on the description. | At 10:00 a.m. on January 15, 2022, an employee, a commissioning engineer, was removing the stop-lugs from a vertically-positioned, side-shifting wire rope carriage on a rail-mounted gantry crane head block when the rope carriage swung down striking the employee in the head and face. The employee was transported to a lo... | 00 |
Predict the fatality based on the description. | At approximately 5:45 a.m. on February 18, 2016, Employee #1 was throwing garbage into the back of a rear load trash truck when he was run over and killed. killed. | 11 |
Predict the fatality based on the description. | At approximately 8:00 a.m. on July 31, 2016, Employee #1 was walking towards a belt man lift as 2 coworkers were pulling in to park on the 6th floor. The coworkers heard a noise and went to the lift opening and yelled for Employee #1 but th ere was no response. Employee #1 was found below dead. | 11 |
Predict the fatality based on the description. | At 11:15 a.m. on August 17, 2018, Employee #1 was clearing a jam on the secondary lactose dryer, Dryer System Number 2. The employee removed the sock/boot from beneath the rotary valve in order to remove the lactose powder that had built up and/or jammed inside the blower pipe. A coworker had just finished opening the ... | 00 |
Predict the fatality based on the description. | At 8:30 a.m. on May 7, 2018, an employee was pulling a wire conduit through an electrical panel of the Trim Press #16 to install lighting fixtures on the press. The employee was tightening a nut bolt and came into contact with live electrical circuits of 480 volts. The employee fell off of a six foot ladder, fracturing... | 00 |
Predict the fatality based on the description. | At 9:26 p.m. on February 9, 2015, Employee #1 was found unresponsive in the office area on site. His death was rule from natural causes | 11 |
Predict the fatality based on the description. | On October 2, 2018, two employees were sampling soils on I-94 when a passing pickup truck that was pulling a trailer was struck by a large truck and spun the trailer into the construction lane, striking both employees. One employee was killed and the second was hospitalized. | 00 |
Predict the fatality based on the description. | At 12:00 p.m. on May 17, 2021, an employee installed gutter on the second story of a building. While working on a ladder, the employee struck their elbow, felt light-headed, and fell approximately twenty feet from the ladder. The employee received an open skull fracture and was killed. | 11 |
Predict the fatality based on the description. | At 10:45 a.m. on February 9, 2021, an employee was walking to the rear of his truck. A a coworker was driving a yard truck between the employee's truck trailer and the loading dock. The coworker's truck struck the employee, who suffered multiple injuries to the torso and was killed. See Investigation summary ID #133172... | 11 |
Predict the fatality based on the description. | At 3:00 p.m. on August 14, 2018, an employee was standing on a D-10 tractor and fell to the ground. The employee sustained a back injury when he struck his head on the ground. The employee was hospitalized. | 00 |
Predict the fatality based on the description. | At 9:15 p.m. on November 22, 2017, an employee was working at the conveyor in th e frozen packing room. The conveyor did not work correctly, and the employee attempted to fix the conveyor by putting pie dough into the sprocket gear and chain. Her hand was caught into the gear resulting in a deep laceration from the pal... | 00 |
Predict the fatality based on the description. | At 4:34 p.m. on April 15, 2019, an employee was run over by a Ford F-350 dually pickup truck while it was backing up and was killed. | 11 |
Predict the fatality based on the description. | At 7:00 a.m. on January 23, 2107, an employee was working on a roof within 6 fee t of a skylight. The employee fell through the skylight approximately 35 feet to the concrete surface below. The employee was killed due to blunt force injuries of the head and chest. | 11 |
Predict the fatality based on the description. | At 5:45 p.m. on March 9, 2019, an employee was repairing a splice when the transfer rollers came down and trapped his head between rollers and drum. The employee fractured his eye socket, nose, and jaw. The employee was hospitalized. hospitalized. | 00 |
Predict the fatality based on the description. | At approximately 8:30 p.m. on November 6, 2021, an employee was stringing new products through equipment using a leader strip. The employee sustained abrasion and compression injuries after being caught in an in-running nip point. The employee and a coworker were working to feed the leader strip (leading edge) of fabri... | 00 |
Predict the fatality based on the description. | At 12:00 a.m. on June 25, 2020, an employee was inspecting the tractor-trailer while standing between the double trailers while it was parked. The coworker returned to the tractor after using the restroom in the maintenance garage. The coworker stated that he did not see the employee and began to pull forward running o... | 11 |
Predict the fatality based on the description. | At 4:45 p.m. on May 15, 2018, Employee #1 was found dead by a coworker on the floor in Building #72. | 11 |
Predict the fatality based on the description. | At 1:00 p.m. on December 3, 2021, an employee was using a Speed Cut Metra-Cut Radial Arm Saw (Model Number SSA-17) to cut 2 x 4 boards into one-foot lengths. The employee was holding the board to be cut in his left hand and operating the radial arm saw with his right. The employee did not adjust the barrier height befo... | 00 |
Predict the fatality based on the description. | At 12:00 p.m. on March 21, 2019, Employee #1 was operating the feed mill elevator from the control panel. The elevator became jammed, so the employee turned the switch off to the elevator leg. He left the controls, and climbed down into the cellar beneath the control panel box stationed on the floor above. As the emplo... | 00 |
Predict the fatality based on the description. | At 7:00 a.m. on September 25, 2018, an employee was driving an electric pallet jack in a refrigerator room in the receiving department and went to turn it. The employee struck the storage racks with the jack and sustained several fractured chest ribs and contusions. The employee was taken to Riverside Community Hospita... | 00 |
Predict the fatality based on the description. | At 9:30 a.m. on November 22, 2017, a truck driver struck another truck head on a nd was killed. | 11 |
Predict the fatality based on the description. | An employee was working as an anesthesia technician in the operating room of a children's hospital when he contracted COVID-19. The employee began feeling ill on November 17, 2020 and was admitted to the hospital on November 19, 2020. The employee died on December 21, 2020, due COVID-19 complications. | 00 |
Predict the fatality based on the description. | At 1:00 a.m. on November 17, 2017, an employee was talking with a team member an d caught his left hand's middle finger between a reefer and a fixture. The empl oyee's finger was amputated and he was hospitalized. | 00 |
Predict the fatality based on the description. | At 12:41 p.m. on April 14, 2016, an employee was working for an auctioneer. He w as closing an industrial overhead garage door. The door had no safety recoil devices to prevent crushing injuries. The employee was crushed and killed when the door closed on him. | 11 |
Predict the fatality based on the description. | At approximately 12:00 a.m. on February 28, 2019, an employee was cleaning the s haft on a rotating turntable with sandpaper while wearing gloves. A glove was c aught by a rotating piece of the machine, unable to let go the employee was hurl ed into the metal framework at the back of booth #4. The employee suffered a p... | 00 |
Predict the fatality based on the description. | At approximately 2:30 p.m. on January 31, 2017, an employee was working in a security guard shack. He suffered a heart attack and died. | 11 |
Predict the fatality based on the description. | At 4:30 a.m. on November 16, 2017, an employee was monitoring a machine and reached into it to free a bag that was caught in it. The employee reached into the machine to free the bag and machine amputated his fingertip. The employee was hospitalized. | 00 |
End of preview. Expand in Data Studio
README.md exists but content is empty.
- Downloads last month
- 8