command stringlengths 2 75 | syntax stringlengths 0 289k | hierarchy_level stringlengths 0 6.91k | description stringlengths 0 45.2k | options listlengths 0 499 | required_privilege_level stringlengths 0 330k | release_information stringlengths 0 3.14k | related_documentation listlengths 0 22 |
|---|---|---|---|---|---|---|---|
addresses (REST API) | addresses [ address-list ]; | [edit system services rest http],
[edit system services rest https] | Specify IP addresses for incoming connections. | [] | system—To view this statement in the configuration.
system-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 14.2. | [] |
adf (Dynamic Firewalls) | adf {
counter;
input-precedence precedence;
not-mandatory;
output-precedence precedence;
rule rule-value;
} | [edit dynamic-profiles profile-name interfaces interface-name unit logical-unit-number family
family filter] | Configure an Ascend-Data-Filter that the dynamic profile applies to a subscriber session. | [
{
"name": "counter",
"desc": "Enable a counter that increments each time the Ascend-Data-Filter rule is used. Typically used"
},
{
"name": "not-mandatory",
"desc": "Suppress router from reporting an error when the RADIUS reply message does not include"
},
{
"name": "precedence",
"des... | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 10.4.
Option not-mandatory introduced in Junos OS Release 12.2. | [
"Understanding Dynamic Firewall Filters",
"Classic Filters Overview",
"Basic Classic Filter Syntax",
"Guidelines for Configuring Service Filters"
] |
adjacency-loss | adjacency-loss; | [edit protocols oam ethernet connectivity-fault-management action-profile action-profile-name
event ais-trigger-condition] | Configure the defect condition that raises an alarm indication signal when physical connectivity is lost
between peer MEPs. | [] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 14.2. | [
"Ethernet Alarm Indication Signal (ETH-AIS) Function Overview",
"Configuring ETH-AIS on a CFM MEP"
] |
adjacency-loss-hold-time (ANCP) | adjacency-loss-hold-time seconds; | [edit protocols ancp],
[edit protocols ancp neighbor ip-address] | Configure the ANCP agent to monitor, either globally or for a specified neighbor, how long an ANCP
adjacency is down and to trigger a state change for the subscriber access line if the hold timer expires
before the adjacency comes back up, as indicated by a Port Up message on the access line. By default,
there is no de... | [
{
"name": "seconds",
"desc": "Duration of period that the ANCP agent monitors loss of adjacency. Default: 0 seconds Range: 0 through 1800 seconds"
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 16.1R4. | [
"Configuring the ANCP Agent to Dampen the Effects of Short-Term Adjacency Losses",
"Configuring ANCP Neighbors",
"Configuring the ANCP Agent",
"Layer 2 Wholesale with ANCP-Triggered VLANs Overview"
] |
adjacency-timer | adjacency-timer seconds; | [edit protocols ancp],
[edit protocols ancp neighbor ip-address] | Specify a value for the interval that the ANCP agent proposes during negotiation to establish an
adjacency, for all neighbors or a specific neighbor. The larger of the values proposed by the agent and
the neighbor is selected for the interval between subsequent adjacency messages exchanged by the
agent and the neighbor... | [
{
"name": "seconds",
"desc": "Number of seconds between adjacency messages."
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 9.4. | [
"Configuring the ANCP Agent",
"Specifying the Interval Between ANCP Adjacency Messages",
"Configuring ANCP Neighbors"
] |
adjust-interval | adjust-interval seconds; | [edit logical-systems logical-system-name protocols mpls label-switched-path lsp-name auto-
bandwidth],
[edit protocols mpls label-switched-path lsp-name auto-bandwidth] | Specify the bandwidth reallocation interval in seconds. | [
{
"name": "seconds",
"desc": "Bandwidth reallocation interval, in seconds."
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Configuring the Automatic Bandwidth Allocation Interval"
] |
adjust-minimum (Dynamic Shaping and Scheduling) | adjust-minimum (rate | $junos-cos-adjust-minimum); | [edit dynamic-profiles profile-name class-of-service schedulers scheduler-name],
[edit dynamic-profiles profile-name class-of-service traffic-control-profiles traffic-control-
profile-name] | For adjustments performed by the ANCP or multicast applications on EQ DPCs and MPC/MIC
interfaces, specify the minimum shaping rate for an adjusted scheduler node. The node is associated
with a traffic-control profile.
For adjustments performed by the multicast application on MPC/MIC interfaces, specify the minimum
sha... | [
{
"name": "rate",
"desc": "Minimum shaping rate for a node or a queue, in Mbps"
},
{
"name": "$junos-cos-adjust-minimum",
"desc": "Junos OS predefined variable that is replaced with the minimum shaping rate"
}
] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 11.4. | [
"Configuring a Dynamic Minimum Adjusted Shaping Rate on Scheduler Nodes",
"Configuring a Dynamic Shaping-Rate Adjustment for Queues"
] |
adjust-minimum | adjust-minimum rate; | [edit class-of-service schedulers scheduler-name],
[edit class-of-service traffic-control-profiles traffic-control-profile-name] | For adjustments performed by the ANCP or multicast applications on EQ DPC, MIC, or MPC interfaces,
specify the minimum shaping rate for an adjusted scheduler node. The node is associated with a traffic-
control profile.
For adjustments performed by the multicast application on MIC or MPC interfaces, specify the minimum... | [
{
"name": "rate",
"desc": "Minimum shaping rate for a node or a queue, in Mbps"
}
] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 11.4. | [
"Configuring the Minimum Adjusted Shaping Rate on Scheduler Nodes for Subscribers"
] |
adjust-percent (Dynamic Schedulers) | adjust-percent percentage; | [edit dynamic-profiles profile-name class-of-service schedulers scheduler-name] | For a MPC/MIC interface, determine the percentage of adjustment for the shaping rate of a queue. | [
{
"name": "percentage",
"desc": "Percentage of the shaping rate to adjust."
}
] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 11.4. | [
"Configuring a Dynamic Shaping-Rate Adjustment for Queues"
] |
adjust-percent | adjust-percent percentage; | [edit class-of-service schedulers scheduler-name] | For a MIC or MPC interface, determine the percentage of adjustment for the shaping rate of a queue. | [
{
"name": "percentage",
"desc": "Percentage of the shaping rate to adjust. Range: 0 through 100 percent"
}
] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 11.4. | [
"Configuring Shaping-Rate Adjustments on Queues"
] |
adjust-threshold | adjust-threshold percent; | [edit logical-systems logical-system-name protocols mpls label-switched-path lsp-name auto-
bandwidth],
[edit protocols mpls label-switched-path lsp-name auto-bandwidth] | Specify in percentage how sensitive the automatic bandwidth adjustment for a label-switched path (LSP)
is to changes in bandwidth utilization.
To specify the changes in the automatic bandwidth adjustment for a LSP in absolute value, use the
"adjust-threshold-absolute" on page 2130 statement instead. | [
{
"name": "percent",
"desc": "Bandwidth demand for the current bandwidth adjustment interval is determined and compared"
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Configuring the Automatic Bandwidth Adjustment Threshold"
] |
adjust-threshold-absolute | adjust-threshold-absolute bps; | [edit logical-systems name protocols mpls label-switched-path name auto-bandwidth],
[edit logical-systems name routing-instances name protocols mpls label-switched-path name auto-
bandwidth],
[edit protocols mpls label-switched-path name auto-bandwidth],
[edit routing-instances name protocols mpls label-switched-path n... | Specify in bits per second how sensitive the automatic bandwidth adjustment for a label-switched path
(LSP) is to changes in the average LSP utilization.
The adjust-threshold-absolute statement works in conjunction with the adjust-threshold statement, which
specifies the change in automatic bandwidth adjustment for an ... | [
{
"name": "bps",
"desc": "Change in average LSP utilization to trigger automatic bandwidth adjustment in bits per second. Default: 0 bps"
}
] | routing | Statement introduced before Junos OS Release 17.4R1. | [
"Configuring the Automatic Bandwidth Adjustment Threshold"
] |
adjust-threshold-activate-bandwidth | adjust-threshold-activate-bandwidth bps; | [edit logical-systems logical-system-name protocols mpls label-switched-path lsp-name auto-
bandwidth],
[edit protocols mpls label-switched-path lsp-name auto-bandwidth] | Specify an absolute value to prevent automatic adjustment of signaled bandwidth and aggressive re-
signaling of a label-switched path (LSP) when the actual bandwidth over the LSP is below the configured
threshold, although the adjust-threshold percentage condition is satisfied. | [
{
"name": "bps",
"desc": "Amount of bandwidth that is compared with the maximum of all traffic samples during an"
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 14.1. | [
"Configuring the Automatic Bandwidth Adjustment Threshold"
] |
adjust-threshold-overflow-limit | adjust-threshold-overflow-limit number; | [edit logical-systems logical-system-name protocols mpls label-switched-path lsp-name auto-
bandwidth],
[edit protocols mpls label-switched-path lsp-name auto-bandwidth] | Specify the number of consecutive bandwidth overflow samples before triggering a bandwidth
adjustment. | [
{
"name": "number",
"desc": "Number of consecutive bandwidth overflow samples."
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 7.5. | [
"Configuring a Limit on Bandwidth Overflow and Underflow Samples"
] |
adjust-threshold-underflow-limit | adjust-threshold-underflow-limit number; | [edit logical-systems logical-system-name protocols mpls label-switched-path lsp-name auto-
bandwidth],
[edit protocols mpls label-switched-path lsp-name auto-bandwidth] | Specify the number of consecutive bandwidth underflow samples before triggering a bandwidth
adjustment. | [
{
"name": "number",
"desc": "Number of consecutive bandwidth underflow samples."
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 11.3. | [
"Configuring a Limit on Bandwidth Overflow and Underflow Samples"
] |
adjustment-control-profiles | adjustment-control-profiles {
profile-name {
application {
(ancp | dhcp-tags | pppoe-tags | radius-coa)
priority priority;
algorithm algorithm;
}
}
} | [edit class-of-service] | Configure the CoS adjustment control profile. | [
{
"name": "profile-name",
"desc": "Name of the adjustment control profile. The remaining statements are explained separately. Search for a statement in CLI Explorer or click a linked statement in the Syntax section for details."
}
] | interfaces—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 13.2. | [
"CoS Adjustment Control Profiles Overview",
"Configuring CoS Adjustment Control Profiles",
"Verifying the CoS Adjustment Control Profile Configuration"
] |
admin-down | admin-down; | [edit logical-systems logical-system-name protocols mpls label-switched-path lsp-name],
[edit protocols mpls label-switched-path lsp-name] | Set a nonpacket GMPLS LSP to the administrative down state. This statement does not affect control
path setup or data forwarding for packet LSPs. | [] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 8.2. | [
"Allowing Nonpacket GMPLS LSPs to Establish Paths Through Routers Running Junos OS"
] |
admin-email | admin-email email-address; | [edit security utm feature-profile anti-virus juniper-express-engine pattern-update email-notify]
[edit security utm feature-profile anti-virus kaspersky-lab-engine pattern-update email-notify]
[edit security utm feature-profile anti-virus sophos-engine pattern-update email-notify]
[edit security utm default-configurat... | You can configure the device to notify a specified administrator when patterns are updated. This is an e-
mail notification with a custom message and a custom subject line. | [] | security—To view this statement in the configuration.
security-control—To add this statement to the configuration. | The Express and Kaspersky antivirus feature is not supported from Junos OS Release 15.1X49-D10
onwards. For previous releases, statement introduced in Junos OS Release 9.5.
The [edit security utm default-configuration] hierarchy level is introduced in Junos OS Release 18.2R1.
Support for Avira engine added in Junos OS ... | [] |
admin-group (Backup Selection) | admin-group {
exclude [ group-name ];
include-all [ group-name ];
include-any [ group-name ];
preference [ group-name ];
} | [edit logical-systems logical-system-name routing-options backup-selection destination prefix
interface interface name],
[edit logical-systems logical-system-name routing-instances instance-name routing-options backup-
selection destination prefix interface interface-name],
[edit routing-instances instance-name routin... | Define the administrative groups criteria for the selection of the backup path.
NOTE: Configure group names of admin-group under the [edit protocols mpls] hierarchy
level. | [
{
"name": "exclude [ group-name ]",
"desc": "Specify the administrative groups to be excluded. The backup path is not selected as the loop-free alternate (LFA) or backup next hop if any of the links in the path have any one of the listed administrative groups."
},
{
"name": "group-name",
"desc":... | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 14.1. | [
"Understanding Backup Selection Policy for IS-IS Protocol",
"Configuring Backup Selection Policy for IS-IS Protocol",
"Understanding Backup Selection Policy for OSPF Protocol",
"backup-selection (Protocols IS-IS)"
] |
admin-group (for Interfaces) | admin-group [ group-names ]; | [edit logical-systems logical-system-name protocols mpls interface interface-name],
[edit protocols mpls interface interface-name] | Define administrative groups for an interface. | [
{
"name": "group-names",
"desc": "One or more names of groups defined with the \"admin-groups\" on page 2149 statement at"
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Configuring Administrative Groups for LSPs"
] |
admin-group (for LSPs) | admin-group {
exclude [ group-names ];
include-all [ group-names ];
include-any [ group-names ];
} | [edit logical-systems logical-system-name protocols mpls],
[edit logical-systems logical-system-name protocols mpls label-switched-path lsp-name],
[edit logical-systems logical-system-name protocols mpls label-switched-path lsp-name (primary |
secondary) path-name],
[edit protocols mpls],
[edit protocols mpls label-sw... | Define the administrative groups to include or exclude an LSP and a path’s primary and secondary paths. | [] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Configuring Administrative Groups for LSPs"
] |
admin-group | admin-group {
exclude [ group-names ];
include-all [ group-names ];
include-any [ group-names ];
} | [edit logical-systems logical-system-name protocols rsvp interface interface-name link-
protection],
[edit logical-systems logical-system-name protocols rsvp interface interface-name link-
protection bypass bypass-name],
[edit protocols rsvp interface interface-name link-protection],
[edit protocols rsvp interface inte... | Enable you to configure administrative groups for bypass label-switched paths (LSPs). You can configure
administrative groups either globally for all bypass LSPs traversing an interface or for just a specific
bypass LSP. | [
{
"name": "exclude group-names",
"desc": "Specify the administrative groups to exclude for a bypass LSP."
},
{
"name": "include-all group-names",
"desc": "Specify the administrative groups whose links the bypass LSP must traverse."
},
{
"name": "include-any group-names",
"desc": "Spe... | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 9.2. | [
"Configuring Administrative Groups for Bypass LSPs"
] |
admin-group-extended | admin-group-extended {
apply-groups group-value;
apply-groups-except group-value;
exclude [ group-values ];
include-all [ group-values ];
include-any [ group-values ];
} | [edit logical-systems logical-system-name protocols mpls],
[edit logical-systems logical-system-name protocols mpls label-switched-path lsp-name],
[edit logical-systems logical-system-name protocols mpls label-switched-path lsp-name (primary |
secondary) path-name],
[edit protocols mpls],
[edit protocols mpls label-sw... | Specifies the group name and group identifier for an administrative group. The group identifier must be
within the range of values specified by the admin-groups-extended-range statement. The extended
administrative group values are global and must be identically configured on all the supported routers
participating in ... | [
{
"name": "apply-groups",
"desc": "Apply the specified administrative groups for the LSP or for the primary and secondary paths."
},
{
"name": "apply-groups-except",
"desc": "Exclude the specified administrative groups from the LSP or from the primary and secondary paths."
},
{
"name": "... | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 11.1. | [
"Configuring Extended Administrative Groups for LSPs",
"Configuring Administrative Groups for LSPs"
] |
admin-groups | admin-groups {
group-name group-value;
} | [edit logical-systems logical-system-name protocols mpls],
[edit protocols mpls] | Configure administrative groups to implement link coloring of resource classes. | [
{
"name": "group-name",
"desc": "Name of the group. You can assign up to 32 names. The names and their corresponding"
},
{
"name": "group-value",
"desc": "Value assigned to the group. The names and their corresponding values must be identical"
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Configuring Administrative Groups for LSPs"
] |
admin-groups-extended | admin-groups-extended group-name {
group-value group-identifier;
} | [edit logical-systems logical-system-name protocols mpls interface interface-name],
[edit logical-systems logical-system-name routing-options],
[edit protocols mpls interface interface-name],
[edit routing-options] | Specifies the group name and group identifier for an administrative group. The group identifier must be
within the range of values specified by the admin-groups-extended-range statement. The extended
administrative group values are global and must be identically configured on all the supported routers
participating in ... | [
{
"name": "group-name",
"desc": "The range of configurable values is between 32 and 4,294,967,295. The range maximum must be greater than the range minimum."
},
{
"name": "group-value group-identifier",
"desc": "The group identifier must be within the range of configurable values, 32 and 4,294,9... | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 11.1. | [
"Configuring Extended Administrative Groups for LSPs",
"Configuring Administrative Groups for LSPs"
] |
admin-groups-extended-range | admin-groups-extended-range {
maximum maximum-number;
mininum minimum-number;
} | [edit logical-systems logical-system-name routing-options],
[edit routing-options] | Enables you to configure extended administrative groups, represented by a 32-bit value, expanding the
number of administrative groups supported in the network beyond just 32. In MPLS traffic engineering,
a link can be configured with a set of administrative groups (also known as colors or resource classes).
Administrat... | [
{
"name": "maximum",
"desc": ""
},
{
"name": "maximum-number",
"desc": "The range of configurable values is between 32 and 4,294,967,295. The range maximum must be greater than the range minimum."
},
{
"name": "minimum",
"desc": ""
},
{
"name": "minimum-number",
"desc": "... | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 11.1. | [
"Configuring Extended Administrative Groups for LSPs",
"Configuring Administrative Groups for LSPs"
] |
admin-search | admin-search {
distinguished-name distinguished-name;
password password;
} | [edit access ldap-options search],
[edit access profile profile-name ldap-options search] | Specify that a Lightweight Directory Access Protocol (LDAP) administrator search is performed. To
perform an administrator search, you must specify administrator credentials, which are used in the bind
as part of performing the search. | [] | access—To view this statement in the configuration.
access-control—To add this statement to the configuration. | Statement introduced in Release 8.5 of Junos OS. | [] |
administrator-email (Security Fallback Block) | administrator-email email-address; | [edit security utm default-configuration]
[edit security utm feature-profile anti-virus juniper-express-engine profile profile-name
notification-options fallback-block]
[edit security utm feature-profile anti-virus kaspersky-lab-engine profile profile-name
notification-options fallback-block]
[edit security utm feat... | Configure the administrator e-mail address that will be notified when a fallback-block occurs. This is an
e-mail notification with a custom message and a custom subject line. | [] | security—To view this statement in the configuration.
security-control—To add this statement to the configuration. | The Express and Kaspersky antivirus feature is not supported from Junos OS Release 15.1X49-D10
onwards. For previous releases, statement introduced in Junos OS Release 9.5. Support for Sophos
engine added in Junos OS Release 11.1.
The [edit security utm default-configuration] hierarchy level is introduced in Junos OS R... | [] |
administrator-email (Security Virus Detection) | administrator-email email address; | [edit security utm default-configuration]
[edit security utm feature-profile anti-virus sophos-engine profile profile name notification-
options virus-detection] | Configure the administrator e-mail address that will be notified when a virus is detected by Sophos
antivirus. This is an e-mail notification with a custom message and a custom subject line. | [] | security—To view this statement in the configuration.
security-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 11.1.
The [edit security utm default-configuration] hierarchy level is introduced in Junos OS Release 18.2R1. | [] |
adsl2-bytes | adsl2-bytes bytes; | [edit protocols ancp qos-adjust] | 17.4R1
Starting in Junos OS Release 17.4R1, this statement is deprecated and replaced by the adsl2-overhead-
bytes option of the access-line statement at the [edit system] hierarchy level. | [
{
"name": "bytes",
"desc": "Number of bytes added to or subtracted from the actual downstream cell overhead. Range: -100 through 100 bytes Default: 0 bytes"
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 17.2.
Statement deprecated in Junos OS Release 17.4R1.
Change History Table
Feature support is determined by the platform and release you are using. Use Feature Explorer to
determine if a feature is supported on your platform.
Release | [
"Configuring the ANCP Agent to Report Traffic Rates to CoS",
"Traffic Rate Reporting and Adjustment by the ANCP Agent",
"Configuring the ANCP Agent"
] |
adsl2-plus-bytes | adsl2-plus-bytes bytes; | [edit protocols ancp qos-adjust] | 17.4R1
Starting in Junos OS Release 17.4R1, this statement is deprecated and replaced by the adsl2-plus-
overhead-bytes option of the access-line statement at the [edit system] hierarchy level. | [
{
"name": "bytes",
"desc": "Number of bytes added to or subtracted from the actual downstream cell overhead. Range: -100 through 100 bytes Default: 0 bytes"
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 17.2.
Statement deprecated in Junos OS Release 17.4R1.
Change History Table
Feature support is determined by the platform and release you are using. Use Feature Explorer to
determine if a feature is supported on your platform.
Release | [
"Configuring the ANCP Agent to Report Traffic Rates to CoS",
"Traffic Rate Reporting and Adjustment by the ANCP Agent",
"Configuring the ANCP Agent"
] |
adsl-bytes | adsl-bytes bytes; | [edit protocols ancp qos-adjust] | 17.4R1
Starting in Junos OS Release 17.4R1, this statement is deprecated and replaced by the adsl-overhead-
bytes option of the access-line statement at the [edit system] hierarchy level. | [
{
"name": "bytes",
"desc": "Number of bytes added to or subtracted from the actual downstream cell overhead. Range: -100 through 100 bytes Default: 0 bytes"
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 17.2.
Statement deprecated in Junos OS Release 17.4R1.
Change History Table
Feature support is determined by the platform and release you are using. Use Feature Explorer to
determine if a feature is supported on your platform.
Release | [
"Configuring the ANCP Agent to Report Traffic Rates to CoS",
"Traffic Rate Reporting and Adjustment by the ANCP Agent",
"Configuring the ANCP Agent"
] |
advance-policy-based-routing | advance-policy-based-routing {
active-probe-params name {
settings {
burst-size <size>;
data-fill fill;
data-size <size>;
dscp-code-points dscp;
forwarding-class fc-name;
loss-priority {
priority (high | low | m... | [edit security] | CAUTION: Enabling tracing can adversely impact scale and performance and may
increase security risk. We strongly recommend using the trace, tracing, or traceoptions
commands only under the guidance of a JTAC support engineer. After collecting the
debug information, immediately disable tracing to minimize risk and resto... | [
{
"name": "profile profile-name",
"desc": "Name of the profile. Must be a unique name with a maximum length of 63 characters."
},
{
"name": "from-zone",
"desc": "Specify a source zone to be associated with the APBR policy."
}
] | services—To view this statement in the configuration.
services-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 15.1X49-D60. | [
"Application Quality of Experience",
"Understanding Advanced Policy-Based Routing"
] |
advance-policy-based-routing-profile (Security Zones) | advance-policy-based-routing-profile profile; | [edit security zones security-zone zone-name] | Enable Advance Policy Based Routing on the specified security zone.
To classify and redirect the traffic, the APBR profile matches applications and application groups and if
the matching rule is found, the packets are routed to the routing instance that sends the traffic to a
different interface as specified in the nex... | [] | services—To view this statement in the configuration.
services-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 15.1X49-D60. | [
"Example: Configuring Advanced Policy-Based Routing for Application-Aware Traffic Management",
"Solution",
"Understanding Advanced Policy-Based Routing"
] |
advanced-anti-malware connection | set services advanced-anti-malware connection (authentication | source-address | source-
interface | url) | Configures the cloud connection, including the hostname, port number and authentication information.
Once configured, a certificate-based mutual authentication and TLS connection is established between
the SRX Series Firewall and Juniper ATP Cloud. The SRX Series Firewall receives configurations from the
cloud and send... | [
{
"name": "authentication tls-profile profile-name",
"desc": "Name of the TLS profile that contains settings for the TLS-secured connection."
},
{
"name": "source-address address",
"desc": "The source IP address to send files to the cloud."
},
{
"name": "source-interface",
"desc": ""... | View
Output Fields
This command produces no output.
Sample Output
set services advanced-anti-malware connection url
user@host# set services advanced-anti-malware connection url https://sky.junipersecurity.net
set services advanced-anti-malware connection authentication
user@host# set services advanced-anti-malware conn... | Command introduced in Junos OS Release 15.1X49-D33. | [
"show services advanced-anti-malware status"
] | |
advanced-anti-malware policy | policy <policy-name>{
blacklist-notification {
log;
}
default-notification {
log;
}
fallback-options {
action [block | permit];
invalid-content-size {
action [block | permit];
notification {
log;
}
}
... | [edit services advanced-anti-malware] | User notification
of malware on
block action
(Starting in Junos 19.3R1) This command allows you to configure HTTP and HTTPS URL
redirection for a customized client notification based on detected malware with the block
action. A block message can only be sent when a block action is configured.
NOTE: See "request service... | [
{
"name": "policy-name",
"desc": "Name of the Juniper Advanced Threat Prevention Cloud policy. NOTE: Starting in Junos OS Release 18.2R1, for unified policies, a default-policy can be used for anti-malware and security-intelligence policies. The commands are: set services security-intelligence default-polic... | View | Command introduced in Junos OS Release 15.1X49-D33.
The SMB option is introduced in Junos OS Release 21.1R1. | [] |
advanced-anti-malware traceoptions | set services advanced-anti-malware traceoptions
<apply-groups name>
<apply-groups-except name>
<file (trace-file-name | files | match | no-world-readable | size | world-readable)>
<flag (all | connection | content | daemon | identification | parser | plugin | policy)>
<level level>
<no-remote-... | CAUTION: Enabling tracing can adversely impact scale and performance and may
increase security risk. We strongly recommend using the trace, tracing, or traceoptions
commands only under the guidance of a JTAC support engineer. After collecting the
debug information, immediately disable tracing to minimize risk and resto... | [
{
"name": "apply-groups",
"desc": ""
},
{
"name": "name",
"desc": "Groups that these trace option settings apply."
},
{
"name": "apply-groups-",
"desc": ""
},
{
"name": "except",
"desc": ""
},
{
"name": "name",
"desc": "Groups that these trace option settings ... | trace—To view this statement in the configuration.
trace-control—To add this statement to the configuration.
Output Fields
This command produces no output. Use the show log trace-file-name command to view the debug file. | Command introduced in Junos OS Release 15.1X49-D33. | [] | |
advertise | (advertise | ignore); | [edit logical-systems logical-system-name protocols router-discovery address address],
[edit protocols router-discovery address address] | Specify whether the server should advertise the IP address in its router advertisement packets:
•
advertise—Advertise the IP address in its router advertisement packets.
•
ignore—Do not advertise the IP addresses in router advertisement packets.
Default
advertise | [] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Understanding the ICMP Protocol for Discovering Gateways to Other Networks",
"Example: Configuring the ICMP Protocol for Discovering Gateways to Other Networks"
] |
advertise-bgp-static | advertise-bgp-static {
policy policy-expression;
} | [edit logical-systems logical-system-name protocols bgp],
[edit logical-systems logical-system-name protocols bgp group group-name],
[edit logical-systems logical-system-name protocols bgp group group-name neighbor address],
[edit protocols bgp],
[edit protocols bgp group group-name],
[edit protocols bgp group group-na... | Include this statement to always advertise a BGP-static route, even if it is not the active route for a
prefix. You can configure this statement globally to advertise the BGP-static routes to all neighbors. You
can also configure this statement to advertise BGP-static routes in a BGP group or to a specific neighbor
in ... | [
{
"name": "policy policy-expression",
"desc": "Specify an additional export policy to control whether or not a given BGP-static route is to be advertised in preference to the active route for a prefix. The policy is applied to the BGP-static route and not to the active route. Only the accept or reject resul... | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 14.2. | [
"Configuring BGP-Static Routes for Preventing Route Flaps",
"Example: Configuring BGP-Static Routes to Prevent Route Flaps",
"Understanding BGP-Static Routes for Preventing Route Flaps"
] |
advertise-external | advertise-external {conditional}; | [edit logical-systems logical-system-name protocols bgp group group-name],
[edit logical-systems logical-system-name protocols bgp group group-name neighbor address],
[edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp
group group-name],
[edit logical-systems logical-system... | Specify BGP to advertise the best external route into an IBGP mesh group, a route reflector cluster, or
an AS confederation even if the best route is an internal route.
In general, deployed BGP implementations do not advertise the external route with the highest local
preference value to internal peers unless it is the... | [
{
"name": "conditional",
"desc": "(Optional) Advertise the best external path only if the route selection process reaches the"
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 9.3. | [
"Example: Configuring a Routing Policy to Advertise the Best External Route to Internal Peers"
] |
advertise-from-main-vpn-tables | advertise-from-main-vpn-tables; | [edit logical-systems logical-system-name protocols bgp],
[edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp],
[edit protocols bgp],
[edit routing-instances routing-instance-name protocols bgp] | Advertise VPN routes from the main VPN tables in the master routing instance (for example,
bgp.l3vpn.0, bgp.mvpn.0) instead of advertising VPN routes from the tables in the VPN routing
instances (for example, instance-name.inet.0, instance-name.mvpn.0). Enable nonstop active routing
(NSR) support for BGP multicast VPN ... | [] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 12.3. | [
"Understanding Junos OS Routing Tables",
"Types of VPNs"
] |
advertise-inactive | advertise-inactive; | [edit logical-systems logical-system-name protocols bgp],
[edit logical-systems logical-system-name protocols bgp group group-name],
[edit logical-systems logical-system-name protocols bgp group group-name neighbor address],
[edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp... | Configure the routing table to export to BGP the best route learned by BGP even if Junos OS did not
select this route to be an active route.
One way to achieve multivendor compatibility is to include the advertise-inactive statement in the
external BGP (EBGP) configuration. By default, BGP stores the route information ... | [] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Example: Configuring BGP to Advertise Inactive Routes",
"Example: Configuring the Preference Value for BGP Routes",
"Example: Configuring BGP Route Preference (Administrative Distance)"
] |
advertise-interval | advertise-interval seconds; | [edit interfaces interface-name unit logical-unit-number family inet address address vrrp-
group group-id],
[edit logical-systems logical-system-name interfaces interface-name unit logical-unit-number
family inet address address vrrp-group group-id] | Configure the interval between Virtual Router Redundancy Protocol (VRRP) IPv4 advertisement packets.
All routers in the VRRP group must use the same advertisement interval.
NOTE: When VRRPv3 is enabled, the advertise-interval statement cannot be used to
configure advertisement intervals. Instead, use the fast-interval ... | [
{
"name": "seconds",
"desc": "Interval between advertisement packets."
}
] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Configuring the Advertisement Interval for the VRRP Primary Router"
] |
advertise-mode (MPLS) | advertise-mode (stub-alias | stub-proxy); | [edit logical-systems logical-system-name protocols mpls egress-protection context-identifier
context-id],
[edit logical-systems logical-system-name protocols mpls label-switched-path lsp-name egress-
protection context-identifier context-id],
[edit protocols mpls egress-protection context-identifier context-id],
[edi... | Configure the method for the interior gateway protocol (IGP) to advertise egress protection availability.
Egress protection availability is advertised in the IGP. Label protocols along with CSPF use this
information to do egress protection. | [
{
"name": "stub-alias",
"desc": "Context identifier has an alias. In the alias method, the LSP end-point address has an explicit backup egress node where the backup node can be learned or configured on the penultimate hop node (PHN) of a protected LSP. With this model, the PHN of a protected LSP sets up the... | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 13.3. | [
"Egress Protection for Layer 3 VPN Edge Protection Overview",
"Example: Configuring Layer 3 VPN Egress Protection with RSVP and LDP"
] |
advertise-peer-as | advertise-peer-as; | [edit logical-systems logical-system-name protocols bgp],
[edit logical-systems logical-system-name protocols bgp group group-name],
[edit logical-systems logical-system-name protocols bgp group group-name neighbor address],
[edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp... | Disable the default behavior of suppressing AS routes.
If you include the advertise-peer-as statement in the configuration, BGP advertises routes learned from
one external BGP (EBGP) peer back to another EBGP peer in the same autonomous system (AS) but not
back to the originating peer.
Another way to disable the route ... | [] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Example: Enabling BGP Route Advertisements",
"Example: Configuring a Layer 3 VPN with Route Reflection and AS Override"
] |
advertise-prefix-sid | advertise-prefix-sid; | [edit fabric protocols bgp],
[edit logical-systems name protocols bgp],
[edit logical-systems name routing-instances name protocols bgp],
[edit logical-systems name tenants name routing-instances name protocols bgp],
[edit protocols bgp],
[edit routing-instances name protocols bgp],
[edit tenants name routing-instances... | Advertise prefix sid to E-BGP peers | [] | routing | Statement introduced in Junos OS Release 20.4R1. | [] |
advertise-srv6-service | advertise-srv6-service; | [edit fabric protocols bgp family inet unicast],
[edit fabric protocols bgp family inet6 unicast],
[edit fabric protocols bgp group name family inet unicast],
[edit fabric protocols bgp group name family inet6 unicast],
[edit fabric protocols bgp group name neighbor name family inet unicast],
[edit fabric protocols bgp... | Enable the egress BGP peer to advertise SRv6 service to a remote provider edge (PE) device. BGP
advertises the reachability of prefixes of a particular service from an egress PE device to ingress PE
nodes through BGP messages. BGP egress nodes advertise a set of reachable prefixes when you enable
BGP Layer 3 services o... | [] | routing | Statement introduced in Junos OS Release 20.4R1. | [
"Overview of SRv6 Network Programming and Layer 3 Services over SRv6 in BGP"
] |
advertise-to-non-llgr-neighbor (Graceful Restart for BGP Helper) | advertise-to-non-llgr-neighbor {
omit-no-export;
} | [edit logical-systems logical-system-name protocols bgp graceful-restart long-lived],
[edit logical-systems logical-system-name protocols bgp group group-name graceful-restart long-
lived],
[edit logical-systems logical-system-name protocols bgp group group-name neighbor address
graceful-restart long-lived],
[edit log... | Enable the BGP long-lived graceful restart (LLGR) stale routes to be advertised to neighbors that do not
advertise the LLGR capability. This setting applies to both routes that were marked LLGR-stale by this
router, and LLGR-stale routes received from neighbors. Ideally, all routers in an autonomous system
support the ... | [] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 15.1 . | [
"Configuring Graceful Restart Options for BGP",
"Junos OS High Availability User Guide"
] |
advertise-zero-ethernet-tag | advertise-zero-ethernet-tag; | [edit routing-instances name protocols evpn] | Advertise EVPN Type 2 (MAC/IP Advertisement) and EVPN Type 3 (Inclusive Multicast Ethernet Tag)
routes with an Ethernet Tag ID value of 0. This statement only applies to instance-type EVPN routing
instances and must have a valid vlan-id and no-normalization configured.
You use the advertise-zero-ethernet-tag configurat... | [] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 24.2R1 | [
"VLAN-Based Service for EVPN"
] |
advertisement (Delay Measurement) | advertisement {
accelerated {
threshold percentage;
}
periodic {
interval seconds;
threshold percentage;
}
} | [edit logical-systems name protocols isis interface name delay-measurement],
[edit logical-systems name routing-instances name protocols isis interface name delay-
measurement],
[edit logical-systems name tenants name routing-instances name protocols isis interface name
delay-measurement],
[edit protocols isis interfa... | Configure link delay advertisement settings. | [
{
"name": "accelerated",
"desc": "Notify the routing process of a change in the link delay measurement parameters for every probe exceeding the configured threshold. NOTE: Configuring the accelerated advertisement option for link delay measurement enables aggressive notifications that result in excessive ne... | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | [
"Understanding Link Delay Measurement and Advertising in IS-IS"
] | |
advertisement | advertisement {
always;
application-specific {
all-applications {
legacy;
}
}
} | [edit logical-systems name protocols isis traffic-engineering],
[edit logical-systems name routing-instances name protocols isis traffic-engineering],
[edit logical-systems name tenants name routing-instances name protocols isis traffic-engineering],
[edit protocols isis traffic-engineering],
[edit routing-instances na... | Advertise TE parameters even if RSVP is not turned on. | [
{
"name": "always",
"desc": "Advertise TE parameters in TE LSAs."
},
{
"name": "application-specific",
"desc": ""
},
{
"name": "all-applications",
"desc": "Use this option to advertise ASLA subtlv. This causes ISIS to advertise all legacy TE attributes inside ASLA sub-TLV as ASLA sub... | routing | [
"traffic-engineering (Protocols IS-IS)"
] | |
advertisement-hold-time | advertisement-hold-time seconds; | [edit logical-systems logical-system-name protocols mpls],
[edit protocols mpls] | Do not advertise when the LSP goes from up to down, for a certain period of time known as the hold
time. | [
{
"name": "seconds",
"desc": "Hold time, in seconds."
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Damping Advertisement of LSP State Changes"
] |
advisory-options (Traffic Shaping) | advisory-options {
downstream-rate rate;
upstream-rate rate;
} | [edit dynamic-profiles profile-name interfaces $junos-interface-ifd-name unit $junos-interface-
unit],
[edit dynamic-profiles profile-name interfaces interface-set $junos-interface-set-name interface
$junos-interface-ifd-name],
[edit interfaces demux0 unit logical-unit-number],
[edit interfaces interface-name unit log... | Specify a recommended shaping rate to be applied to downstream or upstream traffic on an interface.
The remaining statements are explained separately. Search for a statement in CLI Explorer or click a
linked statement in the Syntax section for details. | [] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 11.4.
Support at the [edit interfaces demux0 ...] hierarchy level introduced in Junos OS Release 12.2.
Support at the [edit dynamic-profiles ...] hierarchy level introduced in Junos OS Release 13.1. | [
"Setting a Recommended Shaping Rate for Traffic on ANCP Interfaces",
"Configuring the ANCP Agent",
"Configuring the Method to Derive the LAC Connection Speeds Sent to the LNS"
] |
advpn | advpn {
suggester {
disable;
}
partner {
connection-limit number;
idle-threshold packets/sec;
idle-time seconds;
disable;
}
} | [edit security ike gateway gateway-name] | Enable Auto Discovery VPN (ADVPN) protocol on the specified gateway. ADVPN dynamically
establishes VPN tunnels between spokes to avoid routing traffic through the Hub. When you enable
ADVPN, by default, the Junos OS enables both the suggester and partner roles on the device. You
cannot use the same device with both th... | [
{
"name": "suggester",
"desc": "VPN peer that can initiate a shortcut exchange to allow shortcut partners to establish dynamic security associations (SAs) with each other. Specify disable to disable this role on the gateway. Both suggester and partner roles are enabled if advpn is configured without explici... | security—To view this statement in the configuration.
security-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 12.3X48-D10. The range for the idle-threshold option and the
range and default value for the idle-time option revised in Junos OS Release 12.3X48-D20.
Support for ADVPN with the iked process is added in Junos OS Release 23.4R1. | [
"Understanding Auto Discovery VPN"
] |
af-mode | af-mode; | [edit poe interface (all | interface-name)] | Configure a PoE port on an EX6200 switch to support IEEE 802.3af only. The maximum power the port
can deliver in either class or static mode is 15.4 W.
Default
PoE ports on an EX6200 switch support IEEE 802.3at (PoE+) by default. | [] | system—To view this statement in the configuration.
system-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 11.3. | [
"Configuring PoE Interfaces on EX Series Switches"
] |
af-name | af-name {
peer-gnf {
id peer-gnf-id;
remote-af-name;
}
description af-description;
} | [edit chassis network-slices guest-network-functions gnf id] | Configure abstracted fabric (af) interface between a pair of guest network functions (GNFs). Abstracted
fabric interface is a pseudo interface that represents a first class Ethernet interface behavior. An af
interface is created on a GNF to communicate with the peer GNF when the two GNFs are connected to
each other thr... | [
{
"name": "af-name",
"desc": "Name of the af interface being created on the GNF. Range: af0 through af9"
},
{
"name": "id peer-gnf -id",
"desc": "Name of the GNF peer connected using the af interface. Range: 1 through 10"
},
{
"name": "remote-af-name",
"desc": "Name of the af inter... | system | Statement introduced in Junos OS Release 17.4R1. | [
"Setting Up Junos Node Slicing"
] |
age | age (30m | 10m | 1m | 30s | 10s); | [edit protocols oam ethernet connectivity-fault-management linktrace] | Time to wait (in minutes or seconds) for a response. If no response is received, the request and response
entry is deleted from the linktrace database.
Default
10 minutes | [] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 8.5. | [
"Configuring Linktrace Protocol in CFM"
] |
age-of-attack | age-of-attack
{
greater-than value;
less-than value;
} | [edit security idp dynamic-attack-group name filters] | Age of an Attack. | [
{
"name": "greater-than",
"desc": ""
},
{
"name": "value",
"desc": "Match when age of attack in terms of years is greater than the value (years) specified. NOTE: The first attack was added in the year 2003. So, configuring age greater than 18 will not result in any attacks. Range: 1 year throug... | security | Statement introduced in Junos OS Release 18.2R1. | [] |
agent (Analytics) | agent {
service-agents {
agent-name {
inputs {
analytics {
parameters {
generate-tags value;
sample-frequency value;
sensors file-path;
}
}
... | [edit services analytics] | CAUTION: Enabling tracing can adversely impact scale and performance and may
increase security risk. We strongly recommend using the trace, tracing, or traceoptions
commands only under the guidance of a JTAC support engineer. After collecting the
debug information, immediately disable tracing to minimize risk and resto... | [] | system | Statement introduced in Junos OS Release 18.3R1.
Statement is not supported on Junos OS Evolved. | [
"Configuring the BNG as an IPFIX Mediator to Collect and Export IPFIX Data",
"Configuring the Collection and Export of Local Telemetry Data on the IPFIX Mediator",
"Configuring NTF Agent",
"IPFIX Mediation on the BNG",
"Telemetry Data Collection on the IPFIX Mediator for Export to an IPFIX Collector"
] |
agent-address | agent-address outgoing-interface; | [edit snmp trap-options] | Set the agent address of all SNMPv1 traps generated by this router or switch. Currently, the only option
is outgoing-interface, which sets the agent address of each SNMPv1 trap to the address of the outgoing
interface of that trap. | [
{
"name": "outgoing-interface",
"desc": "Value of the agent address of all SNMPv1 traps generated by this router or switch."
}
] | snmp—To view this statement in the configuration.
snmp-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Configuring the Agent Address for SNMP Traps"
] |
agent-circuit-identifier (Dynamic ACI VLANs) | agent-circuit-identifier {
dynamic-profile profile-name;
} | [edit dynamic-profiles profile-name interfaces $junos-interface-ifd-name unit $junos-interface-
unit auto-configure],
[edit interfaces interface-name unit logical-unit-number auto-configure] | Configure a static or dynamic underlying VLAN interface to enable dynamic VLAN subscriber interface
creation based on agent circuit identifier information.
The remaining statements are explained separately. Search for a statement in CLI Explorer or click a
linked statement in the Syntax section for details. | [] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 12.2. | [
"Configuring Dynamic Underlying VLAN Interfaces to Use Agent Circuit Identifier Information",
"Configuring Static Underlying VLAN Interfaces to Use Agent Circuit Identifier Information"
] |
agent-id | agent-id {
ipv4-address;
inet6 ipv6-address;
} | [edit protocols sflow] | Configure the IP address to be assigned as the agent ID for the sFlow agent. By assigning an IP address,
you ensure that the IP address is not dynamic. You can specify an IPv4 or IPv6 address or both. | [] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 10.2.
Support for IPv6 addresses introduced in Junos OS Release 19.1R1 for MX Series, PTX Series, and QFX
Series devices. | [
"Configuring sFlow Technology for Network Monitoring (CLI Procedure)"
] |
agent-specifier | agent-specifier {
aci circuit-id-string ari remote-id-string {
drop;
delay seconds;
terminate;
dynamic-profile profile-name;
routing-instance routing-instance-name;
static-interface interface-name;
}
} | [edit protocols pppoe service-name-tables table-name service service-name] | Specify the action taken by the interface for the specified agent circuit identifier/agent remote identifier
(ACI/ARI) pair when the interface receives a PPPoE Active Discovery Initiation (PADI) control packet
that includes the vendor-specific tag with ACI/ARI pair information. You can configure an ACI/ARI pair
for a n... | [
{
"name": "aci circuit-id-string",
"desc": "Identifier for the agent circuit ID that corresponds to the DSLAM interface that"
},
{
"name": "ari remote-id-string",
"desc": "Identifier for the subscriber associated with the DSLAM interface that initiated the"
}
] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 10.0.
drop, delay, terminate, dynamic-profile, routing-instance, and static-interface options introduced in Junos OS
Release 10.2. | [
"Configuring PPPoE Service Name Tables",
"Assigning an ACI/ARI Pair to a Service Name and Configuring the Action Taken When the Client",
"Request Includes ACI/ARI Information"
] |
agf | agf {
amfname {
default-amf;
ip-address ip-address;
local-endpoint {
initial-tnla-weight-factor initial-tnla-weight-factor;
ip-address name {
primary;
}
}
node-id node-id;
offline;
port port;
routing-instance routing-instance;
tracking-area name;
}
node-id node-id;
node-name node-nam... | [edit services] | Configure the Access Gateway Function. | [
{
"name": "node-id",
"desc": "Specifies the AGF node identifier. Range: 0 through 255"
},
{
"name": "node-name",
"desc": ""
},
{
"name": "AGF node name",
"desc": ""
}
] | system—To view this statement in the configuration.
system-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 22.3R1. | [] |
aggregate (Gigabit Ethernet CoS Policer) | aggregate {
bandwidth-limit bps;
burst-size-limit bytes;
} | [edit interfaces interface-name gigether-options ethernet-switch-profile ethernet-policer-profile
policer cos-policer-name] | Define a policer to apply to nonpremium traffic.
The remaining statements are explained separately. See CLI Explorer. | [] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Configuring Gigabit Ethernet Policers",
"ieee802.1p"
] |
aggregate (Hierarchical Policer) | aggregate {
if-exceeding {
bandwidth-limit bandwidth;
burst-size-limit burst;
}
then {
discard;
}
} | [edit dynamic-profiles profile-name firewall hierarchical-policer name],
[edit firewall hierarchical-policer] | On M40e, M120, and M320 edge routers with Flexible PIC Concentrator (FPC) input as FFPC and FPC
output as SFPC, and on MX Series, T320, T640, and T1600 edge routers with Enhanced Intelligent
Queuing (IQE) PICs, T4000 routers with Type 5 FPC and Enhanced Scaling Type 4 FPC, configure an
aggregate hierarchical policer.
T... | [] | firewall—To view this statement in the configuration.
firewall-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 9.5.
Support at the [edit dynamic-profiles ... hierarchical-policer name] hierarchy level introduced in Junos OS
Release 11.4. | [
"Hierarchical Policer Configuration Overview",
"Hierarchical Policers",
"bandwidth-limit (Hierarchical Policer)"
] |
aggregate (Protocols RSVP) | (aggregate | no-aggregate); | [edit logical-systems logical-system-name protocols rsvp peer-interface peer-interface-name],
[edit protocols rsvp peer-interface peer-interface-name] | Control the use of RSVP aggregate messages on an interface or peer interface, as described below.
NOTE: Starting in Junos OS Release 15.2, the aggregate statement is deprecated at the
[edit protocols rsvp interface interface-name] and [edit logical-systems logical-system-name
protocols rsvp interface interface-name] hi... | [] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"RSVP Refresh Reduction",
"Configuring RSVP Refresh Reduction"
] |
aggregate (Routing) | aggregate {
defaults {
... aggregate-options ...
}
route destination-prefix {
policy policy-name;
... aggregate-options ...
algorithm number
description description;
}
}
}
} | [edit logical-systems logical-system-name routing-instances routing-instance-name routing-
options],
[edit logical-systems logical-system-name routing-instances routing-instance-name routing-
options rib routing-table-name],
[edit logical-systems logical-system-name routing-options],
[edit logical-systems logical-syste... | Configure aggregate routes. | [
{
"name": "aggregate-options",
"desc": "Additional information about aggregate routes that is included with the route when"
},
{
"name": "active",
"desc": "Removes inactive routes from the forwarding table."
},
{
"name": "passive",
"desc": "Retains inactive routes in the forwarding t... | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Example: Summarizing Static Routes Through Route Aggregation",
"How to Enable SRv6 Network Programming in IS-IS Networks"
] |
aggregate-clients (DHCP Local Server) | aggregate-clients (merge | replace); | [edit logical-systems logical-system-name routing-instances routing-instance-name system
services dhcp-local-server dynamic-profile profile-name],
[edit logical-systems logical-system-name routing-instances routing-instance-name system
services dhcp-local-server group group-name dynamic-profile profile-name],
[edit l... | Specify that the router merge (chain) client attributes such as firewall filters and CoS attributes or
replace them when multiple client sessions exist on the same underlying VLAN.
Not supported for IP demux subscriber interfaces. | [
{
"name": "merge",
"desc": "Aggregate multiple clients attributes for the same subscriber (logical interface)"
},
{
"name": "replace",
"desc": "Replace the entire logical interface whenever a new client logs in to the network using the same"
},
{
"name": "VLAN logical interface",
"de... | system—To view this statement in the configuration.
system-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 9.3.
Options merge and replace introduced in Junos OS Release 9.5. | [
"Attaching Dynamic Profiles to DHCP Subscriber Interfaces or DHCP Client Interfaces"
] |
aggregate-clients (DHCP Relay Agent) | aggregate-clients (merge | replace); | [edit forwarding-options dhcp-relay dhcpv6 dynamic-profile profile-name],
[edit forwarding-options dhcp-relay dynamic-profile profile-name],
[edit forwarding-options dhcp-relay dhcpv6 group group-name dynamic-profile profile-name],
[edit forwarding-options dhcp-relay dual-stack-group dual-stack-group-name dynamic-prof... | Specify that the router merge (chain) client attributes such as firewall filters and CoS attributes or
replace them when multiple client sessions exist on the same underlying VLAN. Use the statement at
the [edit ... dhcpv6] hierarchy levels to configure DHCPv6 support.
M120 and M320 routers do not support DHCPv6.
Not s... | [
{
"name": "merge",
"desc": "Aggregate multiple client attributes for the same subscriber (logical interface)"
},
{
"name": "replace",
"desc": "Replace the entire logical interface whenever a new client logs in to the network using the same"
},
{
"name": "VLAN logical interface",
"des... | system—To view this statement in the configuration.
system-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 9.3.
Options merge and replace introduced in Junos OS Release 9.5.
Support at the [edit ... dhcpv6] hierarchy levels introduced in Junos OS Release 11.4.
Support at the [edit ... dual-stack-group dual-stack-group-name] hierarchy level introduced in Junos OS
Release 15.1. | [
"Attaching Dynamic Profiles to DHCP Subscriber Interfaces or DHCP Client Interfaces",
"Configuring Group-Specific DHCP Relay Options"
] |
aggregate-clients (Static Subscribers) | aggregate-clients (merge | replace); | [edit logical-systems logical-system-name routing-instances routing-instances-name system
services static-subscribers dynamic-profile profile-name],
[edit logical-systems logical-system-name routing-instances routing-instances-name system
services static-subscribers group group-name dynamic-profile profile-name],
[ed... | Specify for all static subscribers or for a group of static subscribers that the router merge (chain)
subscriber (client) attributes such as firewall filters and CoS attributes or replace them when multiple
subscriber sessions exist on the same underlying VLAN. The group version of this statement overrides
the global v... | [
{
"name": "merge",
"desc": "Aggregate the attributes of multiple subscribers for the logical interface."
},
{
"name": "replace",
"desc": "Replace the entire logical interface whenever a new client logs in to the network using the same"
}
] | system—To view this statement in the configuration.
system-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 9.6. | [
"Subscribers over Static Interfaces Configuration Overview",
"Enabling Multiple Subscribers on a VLAN Logical Interface for All Static Subscribers"
] |
aggregate-export-interval | aggregate-export-interval seconds; | [edit forwarding-options accounting name output],
[edit forwarding-options sampling instance instance-name family (inet |inet6 |mpls) output],
[edit forwarding-options sampling family (inet |inet6 |mpls) output] | Specify the duration, in seconds, of the interval for exporting aggregate accounting information. | [
{
"name": "seconds",
"desc": "Duration."
}
] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Configuring Discard Accounting"
] |
aggregate-label | aggregate-label {
community community-name;
} | [edit logical-systems logical-system-name protocols bgp family inet labeled-unicast],
[edit logical-systems logical-system-name protocols bgp family inet6 labeled-unicast],
[edit logical-systems logical-system-name protocols bgp family inet-vpn unicast],
[edit logical-systems logical-system-name protocols bgp family in... | Specify matching criteria (in the form of a community) such that all routes which match are assigned the
same VPN label, selected from one of the several routes in the set defined by this criteria. This reduces
the number of VPN labels that the router must consider, and aggregates the received labels. | [
{
"name": "community community-name",
"desc": "Specify the name of the community to which to apply the aggregate label."
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Configuring Aggregate Labels for VPNs"
] |
aggregate-wait-time | aggregate-wait-time seconds; | [edit interfaces name aggregated-ether-options lacp] | Set the aggregate wait time in seconds for an AE interface. This wait time delays the up event to allow
for the interface state to be programmed before it is brought online. The value can be configured within
a range from 2 to 1800.
NOTE: Starting from Junos OS Release 22.2R1, the range of the aggregate-wait-time
state... | [] | interface—To view this statement in the configuration. | Statement introduced in Junos OS Release 14.2. | [] |
aggregated-devices | aggregated-devices {
ethernet {
device-count number;
}
} | [edit chassis aggregated-devices ethernet device-count number],
[edit chassis aggregated-devices ethernet lacp link-protection non-revertive],
[edit chassis aggregated-devices ethernet lacp system-priority],
[edit chassis aggregated-devices sonet device-count number],
[edit chassis aggregated-devices maximum-links maxi... | Configure properties for aggregated devices on the switch.
Configure properties for aggregated devices on the router. Aggregate Ethernet links are logical
interfaces defined on the device that bundle together multiple physical interfaces into a single interface
for the use of redundancy and bandwidth aggregation. When ... | [] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced for SRX devices in Junos OS Release 7.4.
Statement introduced in Junos OS Release 9.0.
Support for LACP link protection and system priority introduced in Junos OS Release 9.3. | [
"Understanding Aggregated Ethernet Interfaces and LACP for Switches",
"Configuring Link Aggregation",
"Example: Configuring Link Aggregation Between a QFX Series Product and an Aggregation Switch",
"Junos OS Network Interfaces Library for Routing Devices",
"Example: Configuring Aggregated Ethernet High-Spee... |
aggregated-ether | aggregated ether aggregated–ether-group-name; | [edit chassis synchronization source interfaces ] | Specify an aggregated Ethernet group while configuring a member of the group as the clock source. This
is an optional setting. Any number of interfaces from an aggregated Ethernet group can be configured as
the clock source. If a member from the aggregated Ethernet group is selected as the locked clock source,
then all... | [
{
"name": "aggregated–ether-group-name",
"desc": ""
},
{
"name": "aggregated ethernet group name",
"desc": ""
}
] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 17.2R1. | [
"Synchronous Ethernet Overview"
] |
aggregated-ether-options | The fcoe-lag and mc-ae statements are not supported on OCX Series switches.
aggregated-ether-options {
configured-flow-control {
rx-buffers (on | off);
tx-buffers (on | off);
}
ethernet-switch-profile {
tag-protocol-id;
(fcoe-lag | no-fcoe-lag);
(flow-control | no-flow-control);
... | [edit interfaces aex] | Configure aggregated Ethernet-specific interface properties.
NOTE:
•
The fcoe-lag and mc-ae statements are not supported on OCX Series switches.
•
The force-up statement is not supported on QFX10002 switches.
•
The resilient-hash statement is not supported on QFX5200, QFX5210, or QFX10002
switches.
•
On QFX switches, ... | [] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4.
Statements fcoe-lag and no-fcoe-lag introduced in Junos OS Release 13.2X52-D10 for the QFX Series.
Statements force-up, lacp, and resilient-hash introduced in Junos OS Release 14.1X53-D10 for the QFX
Series.
Statement local-minimum-links-threshold introduced in Junos O... | [
"Ethernet Interfaces Overview",
"Understanding Aggregated Ethernet Interfaces and LACP for Switches",
"Configuring Aggregated Ethernet LACP (CLI Procedure)",
"Example: Configuring Link Aggregation with LACP Between a QFX Series Product and an",
"Aggregation Switch",
"Junos OS Network Interfaces Library fo... |
aggregated-inline-services-options (Aggregated Inline Services) | aggregated-inline-services-options {
primary-interface interface-name;
secondary-interface interface-name;
} | [edit interfaces asix] | Configure the members of an aggregated inline service interface bundle to provide 1:1 stateful LNS
redundancy for an LNS sessions in a tunnel group.
BEST PRACTICE: Follow these guidelines:
•
You must configure unit 0 family inet for each bundle; otherwise, the session fails to
come up.
•
The primary (active) and second... | [] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 16.2. | [
"L2TP LNS Inline Service Interfaces",
"L2TP LNS Inline Service Interfaces"
] |
aggregation (Forwarding Options) | aggregation {
autonomous-system;
destination-prefix;
protocol-port;
source-destination-prefix {
caida-compliant;
}
source-prefix;
} | [edit forwarding-options accounting output cflowd hostname],
[edit forwarding-options sampling instance instance-name family (inet |inet6 |mpls) output flow-
server hostname],
[edit forwarding-options sampling family (inet |inet6 |mpls) output flow-server hostname] | For cflowd version 8 only, specify the type of data to be aggregated; cflowd records and sends only
those flows that match the specified criteria. | [
{
"name": "autonomous-system",
"desc": "Aggregate by autonomous system (AS) number."
},
{
"name": "caida-compliant",
"desc": "Record source and destination mask-length values in compliance with the Version 2.1b1"
},
{
"name": "destination-prefix",
"desc": "Aggregate by destination pr... | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Enabling Flow Aggregation",
"Directing Traffic Sampling Output to a Server Running the cflowd Application"
] |
aggregation (IDS) | aggregation {
destination-prefix prefix-value | destination-prefix-ipv6 prefix-value;
source-prefix prefix-value | source-prefix-ipv6 prefix-value;
} | [edit services ids rule rule-name term term-name then] | Configure the IDS rule session limits for individual destination or source subnets rather than individual
addresses. This applies session limits to an aggregation of all attacks from or to a subnet of the specified
length. | [] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Configuring IDS Rules on an MS-DPC",
"Configuring Protection Against Network Attacks on an MS-MPC",
"Understanding IDS on an MS-MPC"
] |
aggregations (IDS Screen Next Gen Services) | aggregations {
destination-prefix-ipv6-mask prefix-length;
destination-prefix-mask prefix-length;
source-prefix-ipv6-mask prefix-length;
source-prefix-mask prefix-length;
} | [edit services screen ids-option screen-name] | Configure intrusion detection service session limits for individual destination subnets or source subnets
rather than individual addresses. This applies session limits to an aggregation of all sessions from or to
an individual subnet of the specified length.
For example, if you configure a value of 24 for destination-p... | [
{
"name": "destination-prefix-ipv6-mask prefix-length",
"desc": "Prefix length for destination IPv6 address subnets. Range: 0 through 128"
},
{
"name": "destination-prefix-mask prefix-length",
"desc": "Prefix length for destination IPv4 address subnets. Range: 0 through 32"
},
{
"name"... | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 19.3R2. | [
"Configuring Network Attack Protection With IDS Screens for Next Gen Services"
] |
aging | aging {
early-ageout seconds;
high-watermark percent;
low-watermark percent;
} | [edit security flow] | The session aging mechanism accelerates the session time-out process when the percentage of entries
in the session table exceeds the high-watermark setting, and then stops when the percentage of entries
in the session table falls below the low-watermark setting. | [] | security—To view this in the configuration.
security-control—To add this to the configuration. | Statement introduced in Junos OS Release 8.5. | [
"Understanding Traffic Processing on Security Devices"
] |
aging-timer (Junos Fusion) | aging-timer aging-timer; | [edit chassis satellite-management] | Configure the aging timer on the aggregation device in a Junos Fusion.
The aging timer is used on the aggregation device to specify the amount of time, in minutes, to maintain
the device state of an unreachable satellite device before deleting the satellite device from the Junos
Fusion.
If the unreachable satellite dev... | [] | admin—To view this statement in the configuration.
admin-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 14.2R3. | [
"Configuring or Expanding a Junos Fusion Enterprise",
"Configuring Junos Fusion Provider Edge"
] |
aigp | aigp [disable]; | [edit logical-systems logical-system-name protocols bgp family inet],
[edit logical-systems logical-system-name protocols bgp family inet6],
[edit logical-systems logical-system-name protocols bgp family inet labeled-unicast],
[edit logical-systems logical-system-name protocols bgp family inet6 labeled-unicast],
[edit ... | The aigp statement enables the Accumulated IGP (AIGP) BGP attribute on a specified protocol family.
Configuring AIGP on a particular family enables the sending and receiving of the AIGP attribute for that
family. AIGP is supported for the following address families:
•
IPv4 unicast
•
IPv6 unicast
•
Labeled unicast
This ... | [
{
"name": "disable",
"desc": "Explicitly disables AIGP."
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 12.1. | [
"Example: Configuring the Accumulated IGP Attribute for BGP"
] |
aigp-adjust (Policy Action) | aigp-adjust (add|divide|multiply|subtract) (user-value | distance-to-protocol-nexthop); | [edit policy-options policy-statement policy-name term term-name then],
[edit policy-options policy-statement policy-name then] | Specify this CLI policy action in an import or export policy to modify the accumulated interior gateway
protocol (AIGP) BGP attribute. You can modify the AIGP attribute for one of the following reasons:
•
Modify the AIGP metric on the route if it exists on the external BGP sessions between two ASBR
routers where there ... | [
{
"name": "add | divide |",
"desc": ""
},
{
"name": "multiply | subtract",
"desc": "Specify the mathematical operation that needs to be performed on the original AIGP attribute for adjustment."
},
{
"name": "user-value",
"desc": "Specify an unsigned 64-bit value in decimal."
},
{... | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 16.1. | [] |
aigp-originate | aigp-originate distance; | [edit logical-systems logical-system-name policy-options policy-statement policy-name term term-
name then],
[edit logical-systems logical-system-name policy-options policy-statement policy-name
then],
[edit policy-options policy-statement policy-name term term-name then],
[edit policy-options policy-s... | Originate an accumulated interior gateway protocol (AIGP) BGP attribute for a given prefix by export
policy, using the aigp-originate policy action.
To originate an AIGP attribure, you need configure the policy action on only one node. The AIGP
attribute is readvertised if the neighbors are AIGP enabled with the aigp s... | [
{
"name": "distance",
"desc": "(Optional) Associate an initial cost when advertising a local prefix with the AIGP BGP attribute."
}
] | routing—To view this statement in the configuration.
routing-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 12.1. | [
"Example: Configuring the Accumulated IGP Attribute for BGP",
"aigp"
] |
ais-trigger-condition | ais-trigger-condition {
adjacency-loss;
all-defects;
cross-connect-ccm;
erroneous-ccm;
receive-ais;
} | [edit protocols oam ethernet connectivity-fault-management action-profile action-profile-name
event] | Configure the defect conditions that generate an alarm indication signal (AIS). | [] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 14.2. | [
"Ethernet Alarm Indication Signal (ETH-AIS) Function Overview",
"Configuring ETH-AIS on a CFM MEP"
] |
alarm (chassis) | alarm
{
fru-absence
{
ignore
{
fpc fpc-name
pem pem-name
... | [edit chassis],
[edit chassis interconnect-device name],
[edit chassis node-group name] | Configure the chassis alarms and whether they trigger a red or yellow alarm, or whether they are
ignored. Red alarm conditions light the RED ALARM LED on either the router’s craft interface or the switch’s
LCD screen and trigger an audible alarm if one is connected to the contact on the craft interface or LCD
screen. Y... | [
{
"name": "alarm-name",
"desc": "Alarm condition. For example, input1, input2"
},
{
"name": "ignore",
"desc": "The specified alarm condition does not set off any alarm."
},
{
"name": "fpc fpc-name",
"desc": "Specify FPC with FPC name or ID."
},
{
"name": "pem pem-name",
"... | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4.
fru-absence option introduced for Junos OS Release 22.4R1. | [
"Alarm Types and Severity Levels",
"Chassis Conditions That Trigger Alarms",
"Chassis Alarm Messages on a QFX3500 Device",
"Interface Alarm Messages"
] |
alarm (optics-options) | alarm low-light–alarm {
(link-down | syslog);
} | [edit interfaces interface-name optics-options],
[edit dynamic-profiles name interfaces name optics-options],
[edit dynamic-profiles name logical-systems name interfaces name optics-options] | Specify the action to take if the receiving optics signal is below the optics low-light alarm threshold.
Starting in Junos OS Release 15.1, for all QSFP-based interfaces, you need not explicitly configure the
syslog option. The syslog option is enabled by default. | [
{
"name": "low-light-alarm",
"desc": "Enable the low light alarm."
},
{
"name": "link-down",
"desc": "Drop the 10-Gigabit Ethernet link and marks link as down."
},
{
"name": "syslog",
"desc": "Write the optics information to the system log."
}
] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 10.0. | [
"Configuring Link Down Notification for Optics Options Alarm or Warning",
"100-Gigabit Ethernet OTN Options Configuration Overview"
] |
alarm (Satellite Policies) | alarm {
linkdown [ignore | red | yellow]
} | [edit policy-options satellite-policies environment-monitoring-policy policy-name] | Configure the link down alarm that is sent within the Junos Fusion whenever a satellite device
experiences a link-down error.
Default
Link-down alarms are not sent on satellite devices in a Junos Fusion until an environment monitoring
policy is configured. | [] | admin—To view this statement in the configuration.
admin-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 14.2R3. | [
"Configuring Satellite Device Alarm Handling Using an Environment Monitoring Satellite Policy in a",
"Junos Fusion",
"Understanding Satellite Policies in a Junos Fusion"
] |
alarm (SNMP RMON) | alarm index {
description description;
falling-event-index index;
falling-threshold integer;
falling-threshold-interval seconds;
interval seconds;
request-type (get-next-request | get-request | walk-request);
rising-event-index index;
rising-threshold integer;
sample-type (absolute-v... | [edit snmp rmon] | Configure RMON alarm entries. | [
{
"name": "index",
"desc": "Identifies this alarm entry as an integer."
}
] | snmp—To view this statement in the configuration.
snmp-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 7.4. | [
"Configuring an RMON Alarm Entry and Its Attributes",
"RMON MIB Event, Alarm, Log, and History Control Tables",
"Monitoring RMON MIB Tables",
"Understanding RMON"
] |
alarm low-light-alarm | alarm low-light–alarm {
(link-down | syslog);
} | [edit interfaces interface-name optics-options] | Specify the action to take if the receiving optics signal is below the optics low-light alarm threshold. | [
{
"name": "link-down",
"desc": "Drop the 10-Gigabit Ethernet link and marks link as down."
},
{
"name": "syslog",
"desc": "Write the optics information to the system log."
}
] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 17.2R1.
Statement introduced in Junos OS Release 18.2R1 for PTX10K-LC1104 on the PTX10008 and
PTX10016 routers. | [
"Configuring Link Down Notification for Optics Options Alarm or Warning",
"100-Gigabit Ethernet OTN Options Configuration Overview"
] |
alarm-id | alarm-id id {
alarm-state state {
description alarm-description;
notification-id notification-id-of-alarm;
resource-prefix alarm-resource-prefix;
varbind-index varbind-index-in-alarm-varbind-list;
varbind-subtree alarm-varbind-subtree;
varbind-value alarm-varbind-valu... | [edit snmp alarm-management alarm-list-name] | Specify the identifier of the alarm that you need to configure.
The remaining statement is explained separately. See CLI Explorer. | [] | snmp—To view this statement in the configuration.
snmp-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 14.1. | [] |
alarm-list-name | alarm-list-name list-name {
alarm-id id {
alarm-state state {
description alarm-description;
notification-id notification-id-of-alarm;
resource-prefix alarm-resource-prefix;
varbind-index varbind-index-in-alarm-varbind-list;
varbind-subtree alarm-... | [edit snmp alarm-management] | Specify the name of the alarm list that you need to configure.
The remaining statements are explained separately. See CLI Explorer. | [] | snmp—To view this statement in the configuration.
snmp-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 14.1. | [] |
alarm-management | alarm-management {
alarm-list-name list-name {
alarm-id id {
alarm-state state {
description alarm-description;
notification-id notification-id-of-alarm;
resource-prefix alarm-resource-prefix;
varbind-index varbind-index-in-alarm-va... | [edit snmp] | Configure the alarm management system to monitor and report active alarms as well as the history of
alarms through the SNMP MIB tables supported by the Alarm MIB.
NOTE: You cannot configure alarms without notifications. It is mandatory to include the
notification identifier in the configuration.
The remaining statement... | [] | snmp—To view this statement in the configuration.
snmp-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 14.1. | [] |
alarm-mode | alarm-mode {
mdi-records-count number;
average;
} | [edit services] | If this statement is configured you can set the alarm as immediate or average mode. If immediate alarm
is configured, an immediate trap is raised at the end of interval duration when the metric value exceeds
the configured range. If average alarm is configured, a trap is generated based on average value for the
specifi... | [
{
"name": "mdi-records-count",
"desc": ""
},
{
"name": "number",
"desc": "Use the specified media delivery index record count number for immediate alarm mode."
},
{
"name": "average",
"desc": "Generate traps for average values that are not within the configured range."
}
] | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 15.1. | [
"Understanding Inline Video Monitoring on MX Series Routers"
] |
alarm-port | alarm-port {
input port port-number {
active {
(high | low);
}
admin-state {
(disabled | enabled);
}
description description;
}
severity {
(critical | major | minor | warning)
}
output port port-number {
adm... | [edit chassis] | Configure an alarm input or output on the dedicated alarm port on the router. You can use the alarm
input configuration to receive alarm inputs from the external devices such as sensors. You can use the
alarm output configuration to relay the alarms in the router to external alarm devices. You can configure
up to three... | [
{
"name": "port-number",
"desc": "Specify the port number for the alarm input or output. The system supports up to three alarm input ports (port number: 1 to 3). The system supports only one alarm output port"
},
{
"name": "(port number: 1)",
"desc": ""
},
{
"name": "active",
"desc":... | interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration. | Statement introduced before Junos OS Release 20.2R1. | [
"Configure Chassis Alarm Input and Output (ACX710 Routers)"
] |
alarm-state | alarm-state state {
description alarm-description;
notification-id notification-id-of-alarm;
resource-prefix alarm-resource-prefix;
varbind-index varbind-index-in-alarm-varbind-list;
varbind-subtree alarm-varbind-subtree;
varbind-value alarm-varbind-value;
} | [edit snmp alarm-management alarm-list-name] | Specify the state of the alarm and the other parameters that you need to monitor. | [
{
"name": "description alarm-description",
"desc": "Include a brief description of the alarm."
},
{
"name": "notification-id notification-id-of-alarm",
"desc": "Specify the identifier of the notification associated with the alarm."
},
{
"name": "resource-prefix alarm-resource-prefix",
... | snmp—To view this statement in the configuration.
snmp-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 14.1. | [] |
alarm-threshold (Security GPRS) | alarm-threshold {
forward number;
reverse number;
} | [edit security gtp profile profile-name path-rate-limit message-type (create-req | delete-req |
echo-req | other)] | Use the alarm-threshold parameter to configure the device to raise an alarm, when the GPRS tunneling
protocol (GTP) control messages on a path have reached the configured limit.
From Junos OS Release 20.4R1 onwards, the [edit security gprs gtp profile profile-name path-rate-limit
message-type (create-req | delete-req |... | [
{
"name": "number",
"desc": "To limit messages in forward or reverse direction."
}
] | security—To view this statement in the configuration.
security-control—To add this statement to the configuration. | Statement introduced in Junos OS Release 12.1X45-D10. | [
"Example: Limiting the Message Rate and Path Rate for GTP Control Messages"
] |
alarm-threshold | alarm-threshold number; | [edit security screen ids-option screen-name tcp syn-flood] | Define the number of half-complete proxy connections per second at which theSRX300, SRX320,
SRX340, SRX345, SRX380, or SRX550M device makes entries in the event alarm log. | [
{
"name": "number",
"desc": "Threshold value."
}
] | security—To view this statement in the configuration.
security-control—To add this statement to the configuration. | Statement modified in Junos OS Release 9.2. | [
"Security Policies Overview"
] |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.